Kit contains

• USB Active Cable
• Micro/USB-C convertor

Software

• Download PC USB driver: http://www.envirosens.com/software/driver/CDM21228_Setup.exe
• Download PC monitor software: http://www.envirosens.com/software/Monitoring.zip
• Download Android (4.3 and higher) monitor software: http://www.envirosens.com/software/ENV_Monitor.apk

How to

1. Install drivers (if needed)
2. Install the software (if needed)
3. Remove batteries from the ENV RD100 meter (not from the ENV RD10)
4. ENV RD100 should be turned OFF (ENV RD10 can be ON or OFF)
5. Connect the meter to the PC/laptop using the special USB Data cable (for Android use adapters) ==> meter will light up and be ON
6. On the software, press “Search Device” ==>
   ENV RD100 display might be empty, LED indication will remain active.
   ENV RD10 LED indication will remain active.
7. On the software, press “Start Recording ” ==> the measurement table and graph on the software will start accumulating the measurement results.
8. Press Mode button on the ENV RD100 , or change the mode switch on the RD10 to change modes of measurements between RF/LFM/LFE (RF Modulation and JONIT MODE are not supported).
9. On the software, press “Stop Recording ” ==> recording and logging will stop.
10. It is possible to save the recording log using the software.

Videos

Connecting and using the ENV RD100 to record EMF measurements on a PC/Laptop

Link – https://youtu.be/NtUBQ-pmN0w?si=r699CHwITYeBMFAv

The post ENV RD10/100 USB Data cable for PC monitoring appeared first on For EHS By EHS.

• CelloEye 24Gs RF detector (light indication & beeping sound!!!)
• It can be used to detect RF sources, RF emissions, and RF radiation up to 24GHz.
• It uses one LED light to show when the RF radiation level is over  0.1m-1W/m2
• Very long (up to 4 years, depending on how often it beeps and blinks) working time using a single CR2032 battery (depending on the RF radiation detection).
• It is not a replacement for an RF/EMF meter, does not indicate RF levels, and is not REAL TIME (does not react to short RF signals).
• It can be glued to walls, windows, and doorsteps, in order to detect RF radiation or if someone enters an RF source into the house.
• Can be carried in your pocket
• Frequency response 0.05-24GHz
  Standard Sensitivity from ~0.1 -1 mW/m2
  10X increased sensitivity ~0.01-0.1 mW/m2 (US10% extra)
  100X increased sensitivity ~0.001-0.01 mW/m2 (US10% extra)
  Weight 18g
  Can work without a battery change for up to 4 years (depending on how often it beeps and blinks).

Possible usage of the CelloEye 24Gs RF Detector

• A very simple RF detector, with “RF exists” or “No RF” indication for training, schools, demos…
• A very simple RF detector for finding RF sources & penetration points in a low RF house.
• A cheap RF detector that can be glued to windows, doors, and walls, to allow detection of incoming RF bursts or when people with RF sources come into the Low EMF house.
• A tiny RF detector to be used by EHS (Electromagnetic Hyper Sensitive) people can carry with them, to alert them of RF radiation when going into places with high RF, or when people with smartphones or wireless devices come close to them.

Sensitivities options

Please note that it is not a replacement for an RF/EMF meter, does not indicate RF levels, and is not REAL TIME (does not react to short RF signals).
Select the required sensitivity (hardware-coded) according to your home RF levels:

• Standard Sensitivity from ~0.1 -1 mW/m2
• 10X increased sensitivity ~0.01-0.1 mW/m2 (US$10 extra)
• 100X increased sensitivity ~0.001-0.01 mW/m2 (US$10 extra)

Spec of CelloEye 24Gs RF Detector

• Model number: CelloEye 24Gs – ENV RD1S (light indication & beeping sound!!!)
• RF detector with one single LED light that lights up, and a beeping sound,  whenever RF radiation is detected above the threshold of 0.1mW/m2
• Run using a single CR2032 battery
• The battery can last up to 4 years (depending on how often it beeps and blinks).
• Weight 18g
• Size
  Height 56mm
  Wide 39mm
  thickness 12mm
• Frequency response 0.05-24GHz
• Sensitivity from 0.1 mW/m2
• You can ask us to increase the detector sensitivity by X10 or X100 – https://www.4ehsbyehs.com/product/increase-sensitivity-celloeye-24gs/
• Manufacture ENVIROSENCE LTD
• Made in Israel
• Sent from Israel
• This RF detector was developed with our close cooperation and according to our requirements so that it would be used by Electromagnetic Hyper Sensitive(EHS) people to detect RF devices and emissions in their houses, and when RF sources are being entered into their homes.

Videos

Link – https://youtu.be/z9NUoMScijM

RF alarm system using the CelloEye 24G RF detectors – https://youtu.be/uBUsmc80sHo

The post CelloEye 24Gs – A TINY RF DETECTOR WITH BEEPING SOUND appeared first on For EHS By EHS.

• CelloEye 24G RF Detector – A Tiny RF detector with light indication only, no beeping sound!!!
  For a version with a beeping sound, please see – https://www.4ehsbyehs.com/product/celloeye-24gs/)
• It can be used to detect RF sources, RF emissions, and RF radiation.
• It uses one LED light to show when the RF radiation level is over  0.1mW/m2
• Very long (up to 4 years) working time using a single CR2032 battery (depending on the RF radiation detection).
• It is not a replacement for an RF/EMF meter, does not indicate RF levels, and is not REAL TIME (does not react to short RF signals).
• It can be glued to walls, windows, and doorsteps, in order to detect RF radiation or if someone enters an RF source into the house.
• Frequency response 0.05-24GHz
• Sensitivity from 0.1-1  mW/m2
• Weight 18g
• Work without a battery change for up to 4 years (depending on how often it blinks)

Possible usage of the CelloEye 24G RF Detector

• A very simple RF detector, with “RF exists” or “No RF” indication for training, schools, demos…
• A very simple RF detector for finding RF sources & penetration points in a low RF house.
• A cheap RF detector that can be glued to windows, doors, and walls, to allow detection of incoming RF bursts or when people with RF sources come into the Low EMF house (if the RF level in your house is lower than 0.1mW/m2).

CelloEye 24G  RF Detector – No sound/beeper

• Model number: CelloEye 24G (light indication only, no beeping sound!!! for a version with beeping sound, please see – https://www.4ehsbyehs.com/product/celloeye-24gs/)
• RF detector with one single LED light that lights up whenever RF radiation is detected above the threshold of 0.1-1 mW/m2
• Run using a single CR2032 battery
• The battery can last up to 4 years (depending on how often it blinks).
• Weight 18g
• Size
  Height 56mm
  Wide 39mm
  thickness 12mm
• Frequency response 0.05-24GHz
• Sensitivity from 0.1-1  mW/m2
• Manufacture ENVIROSENCE LTD
• Made in Israel
• Sent from Israel
• This RF detector was developed with our close cooperation and according to our requirements so that it would be used by Electromagnetic Hyper Sensitive(EHS) people to detect RF devices and emissions in their houses, and when RF sources are being entered into their homes.

Videos about CelloEye 24G RF Detector

Link – https://youtu.be/EzDb5nx94GM

RF alarm system using the CelloEye 24G RF detectors – https://youtu.be/uBUsmc80sHo

The post CelloEye 24 RF DETECTOR appeared first on For EHS By EHS.